Gary
New Member
Posts: 20 
|
Post by Gary on Jul 7, 2015 7:28:58 GMT -7
The G4KLX 1.12 image is working well, however, the SYSINFO email isn't showing the gateway frequency:
DStar Commander V1.12
Gateway ID: G0DNI B
Freq: 000.000
WiFi IP:
192.168.1.81
|
|
|
|
Post by W6KD on Jul 7, 2015 17:24:08 GMT -7
How did you configure DStar Commander? It looks like a valid frequency was not entered at config time. You might try sending an FRQ command via the URCALL field and seeing if that fixes it (i.e. FRQ14475 for 144.75MHz)
Regards
|
|
Gary
New Member
Posts: 20
|
Post by Gary on Jul 7, 2015 23:29:28 GMT -7
Bob,
Thanks for the reply. Interesting point, I'm using 430.0625 but I see that the FRQ command only allows 5 digits and not the 7 that I have. I'll have a play.
|
|
Gary
New Member
Posts: 20
|
Post by Gary on Jul 8, 2015 0:44:09 GMT -7
OK, more testing done, but not there yet.
- My 2 DV Simplex frequencies now changed to 431.050 and 431.060
- FRQ43105 and FRQ43106 commands added to radio (ID51E Plus)
- D-Star Config and Gateway Config set to 431050000 and 430.05000 respectively
- DV Mega/RPI rebooted and all working OK on 431.050
When I issue the FRQ43106 command I get a notification email:
Hotspot freq set to 431.06
Rebooting
- And the RPI reboots (VNC Terminal shows the reboot and closes down)
- After the reboot, the DV Mega is still on 431.050. Running VNC again shows D-Star Config and Gateway Config still set to 431050000 and 430.05000 respectively
So, the command is going from the radio to the DV Mega/RPI and the Pi is rebooting, but the frequency change isn't happening.
Also, if I ask for a SYS Info email, I still get the 000.000 frequency.
DStar Commander V1.12
Gateway ID: G0DNI B
Freq: 000.000
WiFi IP:
192.168.1.81
I must be missing something here?
I'm using the WIFICFG command OK to swap networks and REBOOT and SHUTDOWN are working OK.
|
|
Gary
New Member
Posts: 20
|
Post by Gary on Jul 8, 2015 2:05:25 GMT -7
Update: Fresh V1.12 image installed on new SD card and Headless Basic Setup completed. FRQ command is now working OK, so I must have 'broken' something with my previous config. Need to setup WIFICFG and email alerts on the new image, but all looking good so far  |
|
Gary
New Member
Posts: 20
|
Post by Gary on Jul 8, 2015 3:03:25 GMT -7
Bingo!
DStar Commander V1.12
Gateway ID: G0DNI B
Freq: 431.050
WiFi IP:
192.168.1.81
|
|
john
New Member
Posts: 3
|
Post by john on Jul 23, 2015 21:16:53 GMT -7
I have a similar issue and my question is can I edit a file to have it reflect the correct freq in the SYSINFO report? I haven't set a freq memory yet to send it via my radio. I'm only going to use one so I shouldn't need to change but sure would be nice to see it in the report
|
|
Gary
New Member
Posts: 20
|
Post by Gary on Jul 23, 2015 23:47:45 GMT -7
The SYSINFO email report will show the frequency that the DV Mega is transmitting on. You set that using the G4KLX config utilities (DSTAR Repeater and ircddb config), however, do read the small print in the 'Conventional System Setup' help file in the /doc folder of the G4KLX image zip file. I don't know why my original image was displaying the frequency as 000.000, but starting again with a fresh image did cure the problem.
I'm not sure what you mean when you say you haven't set a radio freq memory yet? You need to have the radio on the DV Mega freq before you can send any commands, specifically the SYSINFO command to get the email/txt report.
|
|
